Rubber Speed Bump, 4' x 12" x 2-1/4" Easy Rider

Rubber Speed Bump, 4' x 12" x 2-1/4" Easy Rider

$224.00 $214.16
(You save $9.84)
Part Number:
PG-ENC-24111
Lead Time:
5 days
Shipping:
Free Shipping on most orders*
Bulk Pricing:
Buy in bulk and save
Size:
4' x 12"
Color:
black
Material:
rubber

Description

Rubber Speed Bump, 4'x12" Easy Rider. Our 4 foot long recycled rubber Easy Rider® speed bumps are easy to install and maintenance free. Molded highly reflective tape ensures that the speed bumps are visible even on a dark night. The speed bumps have a channeled bottom to facilitate drainage as well as to cover cabling or piping. Choose to add optional end caps for a more finished appearance. Install multiple speed bumps end-to-end to make custom lengths.

Features of the Easy-Rider Speed Bumps

Molded highly reflective tape ensures that the speed bumps are visible even on a dark night. Optional cat's eye reflectors further enhance visibility to alert drivers well in advance. The bumps have a channeled bottom to facilitate drainage as well as to cover cabling or piping.
Easy Rider® speed bumps are the ideal maintenance-free parking lot solution. In addition to enhancing parking lot safety, the bumps can lower insurance premiums for lot owners.
The Easy Rider® is available in 4' and 6' lengths including end caps to protect the speed bump ends and vehicles. GNR rubber speed bumps are covered by a 3 year warranty.

View our installation video for the Easy Rider® Speed Bump

Easy Rider® Speed Bumps are:

  • (L) 4' x (W) 12" x (H) 2 1/4"
  • Made of 100% recycled rubber
  • Long lasting and cost efficient
  • Reduces speed to 2-5 mph
  • High visibility at night
  • Simple installation
  • Product can be installed in sections to create varying lengths
  • Will not warp, crack, chip or rot
  • Can be installed on any road surface
  • Resistant to ultraviolet light, moisture, oil, and extreme temperatures
  • Temporary or permanent installation - Relocatable when resurfacing / maintaining road surfaces; products can be stored and re-used
  • Channeled bottom for cabling and piping
  • Lowers insurance premiums for lot owners
  • Maintenance free
  • Warranty: 3 years on the product; 1 year on the tape (under normal use)

Applications:

Used for the following situations:

  • Safety of pedestrian and vehicle traffic requires improvement
  • To further support and reinforce stop signs in parking lots
  • High risk of accidents on residential streets and in parking lots need to be reduced
  • Permanent or temporary lowering speed of motor vehicles is required
  • Only temporary installation is allowed or required
  • Installation on surfaces where only flexible rubber speed bumps may fully conform to the curvature of the road

Technical Specs

Product Name: Rubber Speed Bumps 2 1/4" thick

Models: 6', 4' long

Product description:

1. Material: compression molded composite: 100% recycled rubber and polyurethane prepolymer
2. Physical properties of the rubber composite:
a. Density 0.6 oz/cu in (ASTM C642)
b. Durometer Hardness 70A ± 7 (ASTM D2240)
c. Tensile Strength 300 psi (ASTM D412)
d. Compression deformation 7% at 70psi, 68°F (ASTM D575)
e. Brittleness at Low temperature: -40°F (ASTM D746)
f. Freeze and thaw when exposed to de-icing chemicals no loss after 50 cycles (ASTM C672)
g. Coefficient of thermal expansion: 8 x10-5 in/in/°F (ASTM C531)
h. Weathering 70 hours at 158°F (ASTM D573)
- hardness retained 100% ( ± 5%)
- compressive strength 100% ( ± 5%)
- tensile strength 100% ( ± 5%)
- elongation retained 100% ( ± 5%)

3. Available models: 6', 4' long
4. Finishing: Black recycled rubber composite with yellow, durable and reflective, in-molded pavement marking tape

Components:

a) 100% recycled rubber from car and truck tires (NR, SBR)
b) polyurethane prepolymer
c) cat's eyes reflectors
d) yellow, durable and reflective in-molded pavement marking tape

Extended Information

Installation Guide

Components

  • Easy Rider® speed bumps
  • 1/2" (diameter) , 14" (length) rebar spikes for asphalt or lag bolts with metal shields for concrete - available at GNR
What You Need
  • Gloves, safety glasses
  • Traffic cones, drums or barricades for securing the site
  • Mallet
  • Heavy duty electric drill
  • 1/2" masonry bit and, if installed with lag bolts: a masonry bit required for the metal shields - consult bit size on side of shield
  • A drive socket and power tool for installation of the lag bolts

The flexible design of the Easy Rider® Speed Bump allows the product to conform to the contour of uneven road surfaces and can be installed on both asphalt and concrete.

installation___separator.gif

Installations Instructions for Asphalt: Installation of Easy Rider® Speed Bumps with spikes

Step 1.

Drill 1/2" diameter holes (3 - 4" in depth) in the asphalt through the product's holes.

Step 2.

EasyRiderSpeedBump_Installation1.gif

Drive 1/2" rebar spike (14" long) through the holes in the product.

installation___separator.gif

Installation Instructions for Concrete: Installation of Easy Rider® Speed Bumps with lag bolts and metal shields

Step 1.

Use 1/2" or 5/8 lag bolts (5 1/2" long.)

EasyRiderSpeedBump_Installation2.gif

Step 2.

Drill 1/2" diameter pilot holes (3 - 4" in depth) through the product's installation holes.

Step 3.

Remove the product; re-drill the holes for the diameter and depth required by the metal shields.

Step 4.

Install the metal shields, re-position the product and bolt with lag bolts.

Maintenance

Speed bumps require minimal maintenance. Periodically inspect the bolts and tighten if necessary.

Product Reviews

MPN:
ENC 24111